-------------------------------------------------------------------
**********************
Ambient lightning
**********************
Ambient lighting brightness 1/2
• same brightness as speedometer
• own brightness
Usually the brightness of the ambient lighting is automatically adjusted to the brightness of the speedometer illumination. To set the brightness indepently from the speedometer illumination, set this function to ‘own brightness’. The brightness of the ambient lighting can then be changed with ‘Ambient lighting brightness 2/2’. (codable in FEM)
Ambient lighting brightness 2/2
• very low
• low
• rather low
• medium
• rather high
• high
• very high
Own brightness for ambient lighting. In order to activate this function, set ‘Ambient lighting brightness’ to ‘own brightness’. (codable in FEM)
**********************
Cleaning
**********************
Threshold washer fluid warning
• low
• medium
• high
Threshold at which the washer fluid warning is turned on. The higher the threshold to activate this warning, the sooner this warning will be shown. (codable in FEM)
Number of wipes after windscreen cleaning
• 1
• 2
• 3
• 4
Number of wipes after windscreen is cleaned. (codable in FEM)
Number of wipes after rear window cleaning
• not active
• 1
• 2
• 3
• 4
Number of wipes after rear window is cleaned. (codable in FEM)
Wiping interval rear window
• not active
• 2s
• 4s
• 6s
• 8s
• 10s
• 12s
• 15 s
Interval in seconds for windscreen rear window wipers. (codable in FEM)
Reduce wiper speed
• not active
• 130 kph / 80 mph
• 170 kph / 105 mph
• 210 kph / 130 mph
Threshold at which the wiper speed is reduced. (codable in FEM)
Rear window cleaning with low washer liquid
• active
• not active
Rear windows are also cleaned even though the washer fluid level is low. (codable in FEM)
Wipe delay after windowscreen cleaning
• 0.1 s
• 0.3 s
• 0.5 s
• 0.7 s
Windscreen wipers wipe 0.x seconds after windscreen is cleaned. (codable in FEM)
Wipe delay after rear window cleaning
• 0.1 s
• 0.3 s
• 0.5 s
• 0.7 s
• 0.9 s
• 1.1 s
• 1.3 s
• 1.5 s
Rear window wipers wipe 0.x seconds after rear window is cleaned. (codable in FEM)
Wiping interval standstill
• 3s
• 5s
Interval in seconds for windscreen wipers at standstill. (codable in FEM)
Windscreen wipers continue
• active
• not active
Windscreen wipers don’t stop in the middle of the windscreen when ignition is turned off. Instead they complete their wiping cycle. (codable in FEM)
Number until headlight cleaning
• 1
• 5
• 10
• 15
Head lights are cleaned every x-th time the windscreen washer has been activated. (codable in FEM)
Continue rear wiper when igntion turned on
• active
• not active
Rear wiper continue wiping and don’t interrupt, when the ignition is turned on. (codable in FEM)
Rear wiper permanent when reversing
• active
• not active
When rear wipers are active while reversing, they are automatically set to permament wiping. (codable in FEM)
Head light cleaning
• active
• not active
Turn head light cleaning on/off. (codable in FEM)
Maximum speed headlight cleaning
• 6 kph / 4 mph
• 12 kph / 8 mph
• 30 kph / 19 mph
• 50 kph / 31 mph
• 80 kph / 50 mph
• 130 kph / 80 mph
Maximum speed at which folding headlight cleaning is possible. (codable in FEM)
Number of splashes for head lights
• 1
• 2
• 3
Number of splashes for cleaning the head lights. (codable in FEM)
Length of splash for head lights
• 0.4 s
• 0.6 s
• 0.8 s
• 1.0 s
• 1.2 s
• 1.4 s
• 1.6 s
• 1.8 s
• 2.0 s
Length of a single splash for head light cleaning. (codable in FEM)
Delay between splashes for head lights
• 0.4 s
• 0.6 s
• 0.8 s
• 1.0 s
• 1.2 s
• 1.4 s
• 1.6 s
• 1.8 s
• 2.0 s
Delay between splashes for head light cleaning. (codable in FEM)
Cleanings until 1st headlight cleaning
• not active
• 1
• 3
• 5
• 8
• 10
• 15
Head lights are cleaned for the first time after the x-th time the windscreen washer has been activated. (codable in FEM)
**********************
Clock/Date
**********************
GPS time correction
• active
• not active
Time of day is corrected by using GPS. (codable in KOMBI)
Date incl. Time in dashboard
• active
• not active
Show date including current time in the dashboard. In order to activate this function, please also activate ‘Date in dashboard’. (codable in KOMBI)
**********************
Comfort Functions
**********************
Comfort open sunroof immediately
• active
• not active
Start opening the sunroof immediately during comfort opening. (codable in FEM)
Comfort close sunroof immediately
• active
• not active
Start closing the sunroof immediately during comfort closing. (codable in FEM)
Comfort open windows simultaneously
• active
• not active
Front and back windows open simultaneously during comfort opening. (codable in FEM)
Comfort close windows simultaneously
• active
• not active
Front and back windows close simultaneously during comfort closing. (codable in FEM)
Comfort open using remote
• active
• not active
Press and hold the unlock button on the remote to open all windows and the sunroof. (codable in FEM)
Comfort close using remote
• active
• not active
Press and hold the lock button on the remote to close all windows and the sunroof. (codable in FEM)
Comfort close – door (comfort access)
• active
• not active
Use comfort closing features when locking with the door handle. This only works if comfort access is installed. Touch the locking area on the door handle for a longer time to close all windows and the sunroof. (codable in FEM)
Comfort closing delay (mirrors)
• 0.0s
• 0.5s
• 1.5s
General delay for comfort closing. If ‘0.0s’ is set, mirrors fold immediately when car is locked. (codable in FEM)
**********************
Coming Home
**********************
Extend follow me home lights
• active
• not active
Follow me home lights are displayed longer, when activating the flash to pass again. (codable in FEM)
**********************
Daytime Running Lights
**********************
Daytime running lights – light switch
• not active
• A or 0
• A, 0 or 1
• Low beams
• High beams
Positions for the light switch where the daytime running lights function is activated. (codable in FEM)
**********************
Door lights
**********************
Turn on door lights in reverse gear
• active
• not active
Turn on door lights while car is in reverse. This function can be used to illuminate the area while reversing in order to get a better view of the sides of the car. (codable in FEM)
**********************
Easy Entry
**********************
Easy entry
• active
• not active
If the car is unlocked by pressing the unlock button twice, the driver window will lower as soon as the door is opened. (codable in FEM)
Close window after easy entry
• active
• not active
If the driver side window has been opened via easy entry, the window automatically closes upon locking the vehicle. (codable in FEM)
Easy entry with every door open
• active
• not active
Activate easy entry every time the car is unlocked. If this function is deactivated, the easy entry is activated by pressing the unlock button on the keyfob twice. (codable in FEM)
Easy entry – steering wheel 1/2
• active
• not active
Also adjust the steering wheel position when easy entry is activated. (codable in FEM)
Easy entry – steering wheel 2/2
• active
• not active
Only change this function with ‘Easy entry – steering wheel 1/2’. (codable in FEM)
**********************
Engine Start Stop
**********************
Start/Stop-Automatic memory
• active
• not active
Setting for Start/Stop-Automatic is saved for the next start. Deactivating the Start/Stop-Automatic on the car can increase the life time of the battery and the starter. (codable in FEM)
Start/Stop-Automatic default off
• active
• not active
Engine start/stop automatic is turned off by default. (codable in FEM)
Start/Stop-Automatic enabled in ECO mode
• active
• not active
Engine start/stop automatic is automatically activated in ECO mode. (codable in FEM)
**********************
Gear Shift Indicator
**********************
Gear shift indicator 1/2
• active
• not active
Gear shift indicator in the on board computer. To activate this function, also activate other codings for ‘Gear shift indicator’. (codable in KOMBI)
Gear shift indicator 2/2
• active
• not active
Only change with ‘Gear shift indicator 1/2’. (codable in KOMBI)
Gear shift indicator in sport mode
• active
• not active
Gear shift indicator is also shown in sport mode. (codable in KOMBI)
Gear shift indicator current gear
• active
• not active
Current gear is permanently displayed in the gear shift indicator. (codable in KOMBI)
Gear Shift Indicator menu
• active
• not active
Show menu in the iDrive settings to enable/disable the gear shift indicator. (codable in CIC)
**********************
Headlight Cleaning
**********************
Number until headlight cleaning
• 1
• 5
• 10
• 15
Head lights are cleaned every x-th time the windscreen washer has been activated. (codable in FEM)
Head light cleaning
• active
• not active
Turn head light cleaning on/off. (codable in FEM)
Maximum speed headlight cleaning
• 6 kph / 4 mph
• 12 kph / 8 mph
• 30 kph / 19 mph
• 50 kph / 31 mph
• 80 kph / 50 mph
• 130 kph / 80 mph
Maximum speed at which folding headlight cleaning is possible. (codable in FEM)
Number of splashes for head lights
• 1
• 2
• 3
Number of splashes for cleaning the head lights. (codable in FEM)
Length of splash for head lights
• 0.4 s
• 0.6 s
• 0.8 s
• 1.0 s
• 1.2 s
• 1.4 s
• 1.6 s
• 1.8 s
• 2.0 s
Length of a single splash for head light cleaning. (codable in FEM)
Delay between splashes for head lights
• 0.4 s
• 0.6 s
• 0.8 s
• 1.0 s
• 1.2 s
• 1.4 s
• 1.6 s
• 1.8 s
• 2.0 s
Delay between splashes for head light cleaning. (codable in FEM)
Cleanings until 1st headlight cleaning
• not active
• 1
• 3
• 5
• 8
• 10
• 15
Head lights are cleaned for the first time after the x-th time the windscreen washer has been activated. (codable in FEM)
**********************
iDrive Menus
**********************
Tire pressure menu with temperature
• active
• not active
Also show temperature of the individual tires in the tire pressure menu. This function only works if the tires have tire pressure sensors installed and pressure of the individual tires is already shown. (codable in CIC)
Message length while driving
• no details
• one page
• up to five pages
• whole text
Length of displayed messages for available office functions while driving, e.g. SMS. (codable in CIC)
Sport display
• active
• not active
Sport display for current performance and torque is shown in the ‘Vehicle information’. Since some engines (especially diesel ones) do not provide the data for the sport display to the iDrive, the sport display might be inactive and permanently show ‘0’ even after enabling this function. (codable in CIC)
Sport display – units
• active
• not active
Show menu in the iDrive settings to change the units for the sport display. (codable in CIC)
Gear Shift Indicator menu
• active
• not active
Show menu in the iDrive settings to enable/disable the gear shift indicator. (codable in CIC)
**********************
Instrument Cluster
**********************
Digital speedometer
• active
• not active
The current speed is shown in the digital display below the speedometer. (codable in KOMBI)
Correction’ analog speedometer
• ‘corrected’ speed
• true speed
This coding does not work on US models. Per default the speed shown in the digital speedometer is ‘corrected’ by the car. This has the effect that the shown speed is a bit higher than the true speed of the car. (codable in KOMBI)
Blank information display in dashboard
• active
• not active
Blank information display in dashboard is shown when you switch the information displays with the BC button. (codable in KOMBI)
Date in dashboard
• active
• not active
Show date in dashboard. (codable in KOMBI)
GPS time correction
• active
• not active
Time of day is corrected by using GPS. (codable in KOMBI)
Cruise Control speed display
• not active
• 3 s
• 5 s
The set speed of the cruise control is shown for a couple of seconds in the on board computer. (codable in KOMBI)
Gear shift indicator 1/2
• active
• not active
Gear shift indicator in the on board computer. To activate this function, also activate other codings for ‘Gear shift indicator’. (codable in KOMBI)
Gear shift indicator 2/2
• active
• not active
Only change with ‘Gear shift indicator 1/2’. (codable in KOMBI)
Date incl. Time in dashboard
• active
• not active
Show date including current time in the dashboard. In order to activate this function, please also activate ‘Date in dashboard’. (codable in KOMBI)
Gear shift indicator in sport mode
• active
• not active
Gear shift indicator is also shown in sport mode. (codable in KOMBI)
Bootlogo for dashboard
• BMW
• M
Bootlogo for dashboard when ignition is turned on. This function only works if the dashboard display reaches at least from the middle to under the rpm meter. This coding shows no effect on smaller displays. (codable in KOMBI)
Gear shift indicator current gear
• active
• not active
Current gear is permanently displayed in the gear shift indicator. (codable in KOMBI)
**********************
Interior Lights
**********************
Interior lighting after opening trunk lid
• active
• not active
Interior lighting is turned on, when trunk lid is opened. (codable in FEM)
Brightness interior lights after unlock
• not active
• very low
• low
• rather low
• medium
• rather high
• high
• very high
Brightness of interior lights after unlocking the car. (codable in FEM)
Welcome lights – Innenbeleuchtung
• not active
• very low
• low
• rather low
• medium
• rather high
• high
• very high
Brightness of interior lights for welcome lights. (codable in FEM)
**********************
Legal Disclaimer
**********************
Legal disclaimer (US)
• not active
• active
• permanent
Show legal disclaimer when iDrive is started. This warning is usually only shown in US-models. (codable in CIC)
Camera disclaimer
• not active
• active
• permanent
Show legal disclaimer for rear view camera. (codable in CIC)
Night Vision disclaimer
• not active
• active
• permanent
Show legal disclaimer for night vision view camera. (codable in CIC)
**********************
Locking
**********************
Optical confirmation – locking vehicle
• not active
• 1
• 2
• 3
Number of times the turn signals are turned on when locking the vehicle. (codable in FEM)
Comfort close sunroof immediately
• active
• not active
Start closing the sunroof immediately during comfort closing. (codable in FEM)
Comfort close windows simultaneously
• active
• not active
Front and back windows close simultaneously during comfort closing. (codable in FEM)
Comfort close using remote
• active
• not active
Press and hold the lock button on the remote to close all windows and the sunroof. (codable in FEM)
Comfort close – door (comfort access)
• active
• not active
Use comfort closing features when locking with the door handle. This only works if comfort access is installed. Touch the locking area on the door handle for a longer time to close all windows and the sunroof. (codable in FEM)
Comfort closing delay (mirrors)
• 0.0s
• 0.5s
• 1.5s
General delay for comfort closing. If ‘0.0s’ is set, mirrors fold immediately when car is locked. (codable in FEM)
**********************
Mirrors
**********************
Mirror tilt 1/2
• active
• not active
Requirement for mirror tilt functions. (codable in FEM)
Mirror tilt 2/2
• active
• not active
Requirement for mirror tilt functions. (codable in FEM)
Comfort folding for sideview mirrors
• active
• not active
This function requires an installed LIN-Bus (usually installed with mirror heating).nWhen holding the lock/unlock button on the remote the sideview mirrors automatically fold/unfold. May need additional coding of the ‘CAS’ module. (codable in FEM)
Tilt mirror in reverse
• active
• not active
This function requires an installed LIN-Bus (usually installed with mirror heating).nPassenger mirror is tilted when switching into reverse gear and the mirror switch is set to the driver side. To activate this function activate ‘Mirror tilt’ as well. (codable in FEM)
Mirror tilt while reversing
• weak
• medium
• strong
Tilt of mirrors with activated reverse gear. In order to activate this function, please also activate ‘Tilt mirror in reverse’. (codable in FEM)
Auto-Unfold mirrors
• 1 kph / 1 mph
• 10 kph / 6 mph
• 20 kph / 12 mph
• 40 kph / 25 mph
Speed at which folded mirrors are automatically unfolded. (codable in FEM)
Maximum speed mirror fold
• 10 kph / 6 mph
• 20 kph / 12 mph
• 40 kph / 25 mph
• 60 kph / 37 mph
Maximum speed at which folding the mirrors is possible. (codable in FEM)
Unfold mirrors after comfort close
• active
• not active
Mirrors are automatically unfolded when the car is unlocked, if they were folded by the comfort closing function. (codable in FEM)
Mirror fold with turn signals
• active
• not active
Mirrors can be folded via comfort closing while turn signals or hazard lights are active. (codable in FEM)
**********************
Navigation
**********************
Navigation fuel stop suggestion
• active
• not active
Show suggestions for fuel stops along the way to the destination in ‘Route info’ when navigation system is active. (codable in CIC)
Route Info
• active
• not active
Display the ‘Route Info’ menu. In the ‘Route Info’ menu you can check the current navigation turn by turn. (codable in CIC)
Navigation geo coordinates
• active
• not active
Show geo coordinates in latitude and longitude in the navigation menu. (codable in CIC)
Navigation while updating
• active
• not active
Allow using the navigation system while the maps are being updated. (codable in CIC)
Arrow view in main window
• active
• not active
Arrow view is also available in the main window and not only in the split screen window. (codable in CIC)
Navigation current position
• active
• not active
Show option to display current position in the navigation menu. (codable in CIC)
**********************
Opening
**********************
Easy entry
• active
• not active
If the car is unlocked by pressing the unlock button twice, the driver window will lower as soon as the door is opened. (codable in FEM)
Close window after easy entry
• active
• not active
If the driver side window has been opened via easy entry, the window automatically closes upon locking the vehicle. (codable in FEM)
Easy entry with every door open
• active
• not active
Activate easy entry every time the car is unlocked. If this function is deactivated, the easy entry is activated by pressing the unlock button on the keyfob twice. (codable in FEM)
Optical confirmation – unlocking vehicle
• not active
• 1
• 2
• 3
Number of times the turn signals are turned on when unlocking the vehicle. (codable in FEM)
Comfort open sunroof immediately
• active
• not active
Start opening the sunroof immediately during comfort opening. (codable in FEM)
Comfort open windows simultaneously
• active
• not active
Front and back windows open simultaneously during comfort opening. (codable in FEM)
Comfort open using remote
• active
• not active
Press and hold the unlock button on the remote to open all windows and the sunroof. (codable in FEM)
**********************
Park Distance Control(PDC)
**********************
PDC in reverse
• active
• not active
Activate PDC as soon as car is rolling backwards/reversing. (codable in REM)
PDC turn off – distance limit
• when putting in forward gear
• 1 m / 3 ft
• 10 m / 33 ft
• 25 m / 82 ft
• 50 m / 164 ft
• 75 m / 264 ft
• 100 m / 330 ft
• 150 m / 500 ft
• 200 m / 660 ft
• 250 m / 820 ft
PDC is turned off automatically after driving the set distance in forward gear in one piece. (codable in REM)
PDC turn off – speed limit
• when putting in forward gear
• 1 kph / 1 mph
• 15 kph / 9 mph
• 36 kph / 22 mph
PDC is turned off automatically after driving faster than the set speed in forward gear. (codable in REM)
Reversing camera turn off – distance limit
• when putting in forward gear
• 1 m / 3 ft
• 10 m / 33 ft
• 25 m / 82 ft
• 50 m / 164 ft
• 75 m / 264 ft
• 100 m / 330 ft
• 150 m / 500 ft
• 200 m / 660 ft
• 250 m / 820 ft
Reversing camera is turned off automatically after driving the set distance in forward gear in one piece. (codable in REM)
Reversing camera turn off – speed limit
• when putting in forward gear
• 1 kph / 1 mph
• 15 kph / 9 mph
• 36 kph / 22 mph
Reversing camera is turned off automatically after driving faster than the set speed in forward gear. (codable in REM)
PDC view
• vertical (F-Models)
• horizontal (E-Models)
Direction of park distance control view. (codable in CIC)
**********************
Parking Light
**********************
Parking lights
• active
• not active
Parking lights function is active/not active. One sided parking lights are activated by turning on the turn signals after turning off the ignition and locking the car. (codable in FEM)
**********************
Power Windows
**********************
Continue window action when door is opened
• active
• not active
When the door is opened while its window is opening/closing, the window will continue opening/closing the window. (codable in FEM)
Easy entry
• active
• not active
If the car is unlocked by pressing the unlock button twice, the driver window will lower as soon as the door is opened. (codable in FEM)
Close window after easy entry
• active
• not active
If the driver side window has been opened via easy entry, the window automatically closes upon locking the vehicle. (codable in FEM)
Easy entry with every door open
• active
• not active
Activate easy entry every time the car is unlocked. If this function is deactivated, the easy entry is activated by pressing the unlock button on the keyfob twice. (codable in FEM)
**********************
Rain Light Sensor
**********************
Rain light sensor sensitivity
• very sensitive
• sensitive
• normal
• insensitive
• daytime running lights
Sensitivity of rain light sensor. (codable in FEM)
**********************
Seating Heater
**********************
Seat heater temp. level 1 – armrest front
• 29°C / 84°F
• 32°C / 90°F
• 35°C / 95°F
• 38°C / 100°F
Temperature of the front armrest heater for driver and passenger with front seat heater activated on level 1. (codable in FEM)
Seat heater temp. level 2 – armrest front
• 38°C / 100°F
• 41°C / 106°F
• 44°C / 111°F
Temperature of the front armrest heater for driver and passenger with front seat heater activated on level 2. (codable in FEM)
Seat heater temp. level 3 – armrest front
• 44°C / 111°F
• 47°C / 117°F
• 50°C / 122°F
• 53°C / 127°F
Temperature of the front armrest heater for driver and passenger with front seat heater activated on level 3. (codable in FEM)
Seat heater temp. level 1 – seat front
• 28°C / 82°F
• 31°C / 88°F
• 34°C / 93°F
• 37°C / 99°F
Temperature of the front seat heater for driver and passenger with seat heater activated on level 1. (codable in FEM)
Seat heater temp. level 2 – seat front
• 37°C / 99°F
• 40°C / 104°F
• 43°C / 109°F
Temperature of the front seat heater for driver and passenger with seat heater activated on level 2. (codable in FEM)
Seat heater temp. level 3 – seat front
• 43°C / 109°F
• 46°C / 115°F
• 49°C / 120°F
• 52°C / 126°F
Temperature of the front seat heater for driver and passenger with seat heater activated on level 3. (codable in FEM)
Seat heater temp. level 1 – armrest rear
• 29°C / 84°F
• 32°C / 90°F
• 35°C / 95°F
• 38°C / 100°F
Temperature of the rear armrest heater with rear seat heater activated on level 1. (codable in FEM)
Seat heater temp. level 2 – armrest rear
• 38°C / 100°F
• 41°C / 106°F
• 44°C / 111°F
Temperature of the rear armrest heater with rear seat heater activated on level 2. (codable in FEM)
Seat heater temp. level 3 – armrest rear
• 44°C / 111°F
• 47°C / 117°F
• 50°C / 122°F
• 53°C / 127°F
Temperature of the rear armrest heater with rear seat heater activated on level 3. (codable in FEM)
Seat heater temp. level 1 – seat rear
• 28°C / 82°F
• 31°C / 88°F
• 34°C / 93°F
• 37°C / 99°F
Temperature of the rear seat heater with seat heater activated on level 1. (codable in FEM)
Seat heater temp. level 2 – seat rear
• 37°C / 99°F
• 40°C / 104°F
• 43°C / 109°F
Temperature of the rear seat heater with seat heater activated on level 2. (codable in FEM)
Seat heater temp. level 3 – seat rear
• 43°C / 109°F
• 46°C / 115°F
• 49°C / 120°F
• 52°C / 126°F
Temperature of the rear seat heater with seat heater activated on level 3. (codable in FEM)
**********************
Speedometer
**********************
Digital speedometer
• active
• not active
The current speed is shown in the digital display below the speedometer. (codable in KOMBI)
Correction’ analog speedometer
• ‘corrected’ speed
• true speed
This coding does not work on US models. Per default the speed shown in the digital speedometer is ‘corrected’ by the car. This has the effect that the shown speed is a bit higher than the true speed of the car. (codable in KOMBI)
**********************
Sport display
**********************
Sport display
• active
• not active
Sport display for current performance and torque is shown in the ‘Vehicle information’. Since some engines (especially diesel ones) do not provide the data for the sport display to the iDrive, the sport display might be inactive and permanently show ‘0’ even after enabling this function. (codable in CIC)
Sport display – units
• active
• not active
Show menu in the iDrive settings to change the units for the sport display. (codable in CIC)
**********************
Tank
**********************
Threshold for low range warning
• not active
• 8 km
• 10 km / 6 mi
• 20 km / 12 mi
• 50 km / 31 mi
• 8 mi
• 15 mi
• 30 mi
Threshold for low range warning due to low fuel level. (codable in KOMBI)
**********************
Telephone
**********************
Message length while driving
• no details
• one page
• up to five pages
• whole text
Length of displayed messages for available office functions while driving, e.g. SMS. (codable in CIC)
**********************
Turn signals
**********************
Optical confirmation – unlocking vehicle
• not active
• 1
• 2
• 3
Number of times the turn signals are turned on when unlocking the vehicle. (codable in FEM)
Optical confirmation – locking vehicle
• not active
• 1
• 2
• 3
Number of times the turn signals are turned on when locking the vehicle. (codable in FEM)
One-touch turn signal function
• 1
• 3
• 5
• 7
Number of turn signals when tapping the turn signal. In some cases, this option also needs to be enabled in the iDrive. (codable in FEM)
**********************
Video in Motion
**********************
Video in motion 1/3
• not active
• 3 kph / 2 mph
• 8 kph / 5 mph
• active
Enable video and DVD while driving. This is only possible if the car supports watching TV or playing DVDs while standing. In order to enable this option, activate ‘Video in motion 2/3’ and ‘Video in motion 3/3’ as well. If available, also disable ‘Video only with handbrake’. (codable in CIC)
Video in motion 2/3
• not active
• 3 kph / 2 mph
• 10 kph / 6 mph
• active
Only change this function with ‘Video in motion 1/3’. This is only possible if the car supports watching TV or playing DVDs while standing. (codable in CIC)
Video in motion 3/3
• active
• not active
Only change this function with ‘Video in motion 1/3’. This is only possible if the car supports watching TV or playing DVDs while standing. (codable in CIC)
**********************
Voltage Monitoring
**********************
Low beams left voltage monit. 1/2
• active
• not active
Voltage monitoring for low beams left. Might cause flickering of LED lights. (codable in FEM)
Low beams left voltage monit. 2/2
• active
• not active
Deactivate with ‘Low beams left voltage monit. 1/2’ to disable flickering of LED lights. (codable in FEM)
Low beams right voltage monit. 1/2
• active
• not active
Voltage monitoring for low beams right. Might cause flickering of LED lights. (codable in FEM)
Low beams right voltage monit. 2/2
• active
• not active
Deactivate with ‘Low beams right voltage monit. 1/2’ to disable flickering of LED lights. (codable in FEM)
High beams left voltage monit. 1/2
• active
• not active
Voltage monitoring for high beams left. Might cause flickering of LED lights. (codable in FEM)
High beams left voltage monit. 2/2
• active
• not active
Deactivate with ‘High beams left voltage monit. 1/2’ to disable flickering of LED lights. (codable in FEM)
High beams right voltage monit. 1/2
• active
• not active
Voltage monitoring for high beams right. Might cause flickering of LED lights. (codable in FEM)
High beams right voltage monit. 2/2
• active
• not active
Deactivate with ‘High beams right voltage monit. 1/2’ to disable flickering of LED lights. (codable in FEM)
Turn signals front left voltage monit. 1/2
• active
• not active
Voltage monitoring for turn signals front left. Might cause flickering of LED lights. (codable in FEM)
Turn signals front left voltage monit. 2/2
• active
• not active
Deactivate with ‘Turn signals front left voltage monit. 1/2’ to disable flickering of LED lights. (codable in FEM)
Turn signals front right voltage monit. 1/2
• active
• not active
Voltage monitoring for turn signals front right Might cause flickering of LED lights. (codable in FEM)
Turn signals front right voltage monit. 2/2
• active
• not active
Deactivate with ‘Turn signals front right voltage monit. 1/2’ to disable flickering of LED lights. (codable in FEM)
Front fog lights left voltage monit. 1/2
• active
• not active
Voltage monitoring for front fog lights left. Might cause flickering of LED lights. (codable in FEM)
Front fog lights left voltage monit. 2/2
• active
• not active
Deactivate with ‘Front fog lights left voltage monit. 1/2’ to disable flickering of LED lights. (codable in FEM)
Front fog lights right voltage monit. 1/2
• active
• not active
Voltage monitoring for front fog lights right. Might cause flickering of LED lights. (codable in FEM)
Front fog lights right voltage monit. 2/2
• active
• not active
Deactivate with ‘Front fog lights right voltage monit. 1/2’ to disable flickering of LED lights. (codable in FEM)
Daytime running lights left voltage monit. 1/2
• active
• not active
Voltage monitoring for daytime running lights left. Might cause flickering of LED lights. (codable in FEM)
Daytime running lights left voltage monit. 2/2
• active
• not active
Deactivate with ‘Daytime running lights left voltage monit. 1/2’ to disable flickering of LED lights. (codable in FEM)
Daytime running lights right voltage monit. 1/2
• active
• not active
Voltage monitoring for daytime running lights right. Might cause flickering of LED lights. (codable in FEM)
Daytime running lights right voltage monit. 2/2
• active
• not active
Deactivate with ‘Daytime running lights right voltage monit. 1/2’ to disable flickering of LED lights. (codable in FEM)
Turn signals front left warning
• active
• not active
Warning for malfunction of Turn signals front left in the on board computer. (codable in FEM)
Turn signals front right warning
• active
• not active
Warning for malfunction of Turn signals front right in the on board computer. (codable in FEM)
Turn signals rear left voltage monit. 1/2
• active
• not active
Voltage monitoring for turn signals rear left. Might cause flickering of LED lights. (codable in REM)
Turn signals rear left voltage monit. 2/2
• active
• not active
Deactivate with ‘Turn signals rear left voltage monit. 1/2’ to disable flickering of LED lights. (codable in REM)
Turn signals rear right voltage monit. 1/2
• active
• not active
Voltage monitoring for turn signals rear right. Might cause flickering of LED lights. (codable in REM)
Turn signals rear right voltage monit. 2/2
• active
• not active
Deactivate with ‘Turn signals rear right voltage monit. 1/2’ to disable flickering of LED lights. (codable in REM)
Standing lights outer rear left voltage monit. 1/2
• active
• not active
Voltage monitoring for outer standing lights rear left. Might cause flickering of LED lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in REM)
Standing lights outer rear left voltage monit. 2/2
• active
• not active
Deactivate with ‘Standing lights outer rear left voltage monit. 1/2’ to disable flickering of LED lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in REM)
Standing lights outer rear right voltage monit. 1/2
• active
• not active
Voltage monitoring for outer standing lights rear right. Might cause flickering of LED lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in REM)
Standing lights outer rear right voltage monit. 2/2
• active
• not active
Deactivate with ‘Standing lights outer rear right voltage monit. 1/2’ to disable flickering of LED lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in REM)
Standing lights inner rear left voltage monit. 1/2
• active
• not active
Voltage monitoring for inner standing lights rear left. Might cause flickering of LED lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in REM)
Standing lights inner rear left voltage monit. 2/2
• active
• not active
Deactivate with ‘Standing lights inner rear left voltage monit. 1/2’ to disable flickering of LED lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in REM)
Standing lights inner rear right voltage monit. 1/2
• active
• not active
Voltage monitoring for inner standing lights rear right. Might cause flickering of LED lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in REM)
Standing lights inner rear right voltage monit. 2/2
• active
• not active
Deactivate with ‘Standing lights inner rear right voltage monit. 1/2’ to disable flickering of LED lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in REM)
Reversing lights left voltage monit. 1/2
• active
• not active
Voltage monitoring for reversing lights left. Might cause flickering of LED lights. (codable in REM)
Reversing lights left voltage monit. 2/2
• active
• not active
Deactivate with ‘Reversing lights left voltage monit. 1/2’ to disable flickering of LED lights. (codable in REM)
Reversing lights right voltage monit. 1/2
• active
• not active
Voltage monitoring for reversing lights right. Might cause flickering of LED lights. (codable in REM)
Reversing lights right voltage monit. 2/2
• active
• not active
Deactivate with ‘Reversing lights right voltage monit. 1/2’ to disable flickering of LED lights. (codable in REM)
Rear fog light left voltage monit. 1/2
• active
• not active
Voltage monitoring for rear left fog light. Might cause flickering of LED lights. (codable in REM)
Rear fog light left voltage monit. 2/2
• active
• not active
Deactivate with ‘Rear fog light left voltage monit. 1/2’ to disable flickering of LED lights. (codable in REM)
Rear fog light right voltage monit. 1/2
• active
• not active
Voltage monitoring for rear right fog light. Might cause flickering of LED lights. (codable in REM)
Rear fog light right voltage monit. 2/2
• active
• not active
Deactivate with ‘Rear fog light right voltage monit. 1/2’ to disable flickering of LED lights. (codable in REM)
Brake lights left voltage monit. 1/2
• active
• not active
Voltage monitoring for brake lights left. Might cause flickering of LED lights. (codable in REM)
Brake lights left voltage monit. 2/2
• active
• not active
Deactivate with ‘Brake lights left voltage monit. 1/2’ to disable flickering of LED lights. (codable in REM)
Brake lights right voltage monit. 1/2
• active
• not active
Voltage monitoring for brake lights right. Might cause flickering of LED lights. (codable in REM)
Brake lights right voltage monit. 2/2
• active
• not active
Deactivate with ‘Brake lights right voltage monit. 1/2’ to disable flickering of LED lights. (codable in REM)
Third brake light voltage monit. 1/2
• active
• not active
Voltage monitoring for third brake light. Might cause flickering of LED lights. (codable in REM)
Third brake light voltage monit. 2/2
• active
• not active
Deactivate with ‘Third brake light voltage monit. 1/2’ to disable flickering of LED lights. (codable in REM)
License plate lighting voltage monit. 1/2
• active
• not active
Voltage monitoring for license plate lighting. Might cause flickering of LED lights. (codable in REM)
License plate lighting voltage monit. 2/2
• active
• not active
Deactivate with ‘License plate lighting voltage monit. 1/2’ to disable flickering of LED lights. (codable in REM)
**********************
Warnings
**********************
Threshold for low range warning
• not active
• 8 km
• 10 km / 6 mi
• 20 km / 12 mi
• 50 km / 31 mi
• 8 mi
• 15 mi
• 30 mi
Threshold for low range warning due to low fuel level. (codable in KOMBI)
Reverse gear gong
• active
• not active
Gong for reverse gear is active/not active. (codable in KOMBI)
Low beams left warning
• not active
• active
• active (alternative)
Warning for malfunction of Low beams left in the on board computer. (codable in FEM)
Low beams right warning
• not active
• active
• active (alternative)
Warning for malfunction of Low beams right in the on board computer. (codable in FEM)
High beams left warning
• active
• not active
Warning for malfunction of High beams left in the on board computer. (codable in FEM)
High beams right warning
• active
• not active
Warning for malfunction of High beams right in the on board computer. (codable in FEM)
Front fog lights left warning
• not active
• active
• active (alternative)
Warning for malfunction of Front fog lights left in the on board computer. (codable in FEM)
Front fog lights right warning
• active
• not active
Warning for malfunction of Front fog lights right in the on board computer. (codable in FEM)
Daytime running lights left warning
• not active
• active
• active (alternative)
Warning for malfunction of Daytime running lights left in the on board computer. (codable in FEM)
Daytime running lights right warning
• not active
• active
• active (alternative)
• active (Japan)
Warning for malfunction of Daytime running lights right in the on board computer. (codable in FEM)
Turn signals rear left warning
• active
• not active
Warning for malfunction of Turn signals rear left in the on board computer. (codable in REM)
Turn signals rear right warning
• active
• not active
Warning for malfunction of Turn signals rear right in the on board computer. (codable in REM)
Standing lights outer rear left warning
• active
• not active
Warning for malfunction of outer rear left standing lights in the on board computer. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in REM)
Standing lights outer rear right warning
• active
• not active
Warning for malfunction of outer rear right standing lights in the on board computer. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in REM)
Standing lights inner rear left warning
• active
• not active
Warning for malfunction of inner rear left standing lights in the on board computer. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in REM)
Standing lights inner rear right warning
• active
• not active
Warning for malfunction of inner rear right standing lights in the on board computer. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in REM)
Reversing lights left warning
• active
• not active
Warning for malfunction of left reversing lights in the on board computer. (codable in REM)
Reversing lights right warning
• active
• active (alternative)
• not active
Warning for malfunction of right reversing lights in the on board computer. (codable in REM)
Rear fog light left warning
• active
• active (alternative)
• active (alternative)
• not active
Warning for malfunction of rear left fog light in the on board computer. (codable in REM)
Rear fog light right warning
• active
• active (alternative)
• not active
Warning for malfunction of rear right fog light in the on board computer. (codable in REM)
Brake lights left warning
• active
• not active
Warning for malfunction of left braking lights in the on board computer. (codable in REM)
Brake lights right warning
• active
• not active
Warning for malfunction of right braking lights in the on board computer. (codable in REM)
Third brake light warning
• active
• not active
Warning for malfunction of third brake light in the on board computer. (codable in REM)
License plate light warning
• active
• not active
Warning for malfunction of license plate lights in the on board computer. (codable in REM)
Seat belt reminder driver
• active
• not active
Seat belt reminder for driver is active/ inactive. (codable in CSM)
Seat belt reminder passenger
• active
• not active
Seat belt reminder for passenger is active/ inactive. (codable in CSM)
Seat belt reminder – distance
• 100 m / 330 ft
• 200 m / 660 ft
• 500 m / 0.31 mls
• 1000 m / 0.62 mls
Seat belt reminder is activated after driving the set distance and driving faster than the set speed. Use ‘Seat belt reminder – speed’ to set the speed. (codable in CSM)
Seat belt reminder – speed
• 10 kph / 6 mph
• 20 kph / 12 mph
• 30 kph / 19 mph
• 50 kph / 31 mph
Seat belt reminder is activated after driving the set distance and driving faster than the set speed. Use ‘Seat belt reminder – distance’ to set the distance. (codable in CSM)
**********************
Welcome Light
**********************
Welcome lights
• active
• not active
Welcome lights are turned on, when vehicle is unlocked. In order for the welcome light to work, the light switch in the car has to be set to ‘Auto’. In some cases, this option also needs to be enabled in the iDrive. In order to customize which lights should be turned on, please use the following options. (codable in FEM)
Welcome-lights – light switch position
• not active
• A
• A or 2
Positions for the light switch where the welcome-lights function is activated. (codable in FEM)
Welcome lights – brightness
• off
• very low
• low
• medium
• high
• very high
Brightness of exterior lights for welcome lights. (codable in FEM)
Welcome lights duration
• 10s
• 20s
• 40s
• 90s
• 150s
• 240s
Duration of the welcome lights in seconds. (codable in FEM)
Welcome lights – standing lights front left
• not active
• turn on softly
• turn on hard
Standing lights front left are turned on with welcome lights. (codable in FEM)
Welcome lights – standing lights front right
• not active
• turn on softly
• turn on hard
Standing lights front right are turned on with welcome lights. (codable in FEM)
Welcome lights – DRL left
• not active
• turn on softly
• turn on hard
Daytime running lights left are turned on with welcome lights. (codable in FEM)
Welcome lights – DRL right
• not active
• turn on softly
• turn on hard
Daytime running lights right are turned on with welcome lights. (codable in FEM)
Welcome lights – low beams left
• not active
• turn on softly
• turn on hard
Low beams left are turned on with welcome lights. (codable in FEM)
Welcome lights – low beams right
• not active
• turn on softly
• turn on hard
Low beams right are turned on with welcome lights. (codable in FEM)
Welcome lights – turn signal front left
• not active
• turn on softly
• turn on hard
Turn signal front left are turned on with welcome lights. (codable in FEM)
Welcome lights – turn signal front right
• not active
• turn on softly
• turn on hard
Turn signal front right are turned on with welcome lights. (codable in FEM)
Welcome lights – turn signal mid left
• not active
• turn on softly
• turn on hard
Turn signal mid (mirrors) left are turned on with welcome lights. (codable in FEM)
Welcome lights – turn signal mid right
• not active
• turn on softly
• turn on hard
Turn signal mid (mirrors) right are turned on with welcome lights. (codable in FEM)
Welcome lights – design lights left
• not active
• turn on softly
• turn on hard
Design lights left are turned on with welcome lights. (codable in FEM)
Welcome lights – design lights right
• not active
• turn on softly
• turn on hard
Design lights right are turned on with welcome lights. (codable in FEM)
Welcome lights – high beams left
• not active
• turn on softly
• turn on hard
High beams left are turned on with welcome lights. (codable in FEM)
Welcome lights – high beams right
• not active
• turn on softly
• turn on hard
High beams right are turned on with welcome lights. (codable in FEM)
Welcome lights – front fog lights left
• not active
• turn on softly
• turn on hard
Front fog lights left are turned on with welcome lights. (codable in FEM)
Welcome lights – front fog lights right
• not active
• turn on softly
• turn on hard
Front fog lights right are turned on with welcome lights. (codable in FEM)
Brightness interior lights after unlock
• not active
• very low
• low
• rather low
• medium
• rather high
• high
• very high
Brightness of interior lights after unlocking the car. (codable in FEM)
Welcome lights – Innenbeleuchtung
• not active
• very low
• low
• rather low
• medium
• rather high
• high
• very high
Brightness of interior lights for welcome lights. (codable in FEM)
Welcome lights – only when dark
• active
• not active
Welcome lights are only turned on when the rain-light sensor (RLS) recognizes it is dark outside. Only works if rain-light sensor is installed. (codable in FEM)
Welcome lights – turn signals rear left
• not active
• turn on softly
• turn on hard
Turn signals rear left are turned on with welcome lights. (codable in REM)
Welcome lights – turn signals rear right
• not active
• turn on softly
• turn on hard
Turn signals rear right are turned on with welcome lights. (codable in REM)
Welcome lights – stand. lights outer rear left
• not active
• turn on softly
• turn on hard
Outer standing lights rear left are turned on with welcome lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in REM)
Welcome lights – stand. lights outer rear right
• not active
• turn on softly
• turn on hard
Outer standing lights rear right are turned on with welcome lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in REM)
Welcome lights – stand. lights inner rear left
• not active
• turn on softly
• turn on hard
Inner standing lights rear left are turned on with welcome lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in REM)
Welcome lights – stand. lights inner rear right
• not active
• turn on softly
• turn on hard
Inner standing lights rear right are turned on with welcome lights. The outer standing lights are on the car itself, the inner ones are on the rear lid (if available). (codable in REM)
Welcome lights – reversing lights left
• not active
• turn on softly
• turn on hard
Reversing lights left are turned on with welcome lights. (codable in REM)
Welcome lights – reversing lights right
• not active
• turn on softly
• turn on hard
Reversing lights right are turned on with welcome lights. (codable in REM)
Welcome lights – rear fog lights left
• not active
• turn on softly
• turn on hard
Rear left fog lights are turned on with welcome lights. (codable in REM)
Welcome lights – rear fog lights right
• not active
• turn on softly
• turn on hard
Rear right fog lights are turned on with welcome lights. (codable in REM)
Welcome lights – braking lights left
• not active
• turn on softly
• turn on hard
Braking lights left are turned on with welcome lights. (codable in REM)
Welcome lights – braking lights right
• not active
• turn on softly
• turn on hard
Braking lights right are turned on with welcome lights. (codable in REM)
Welcome lights – third brake light
• not active
• turn on softly
• turn on hard
Third brake light is turned on with welcome lights. (codable in REM)
Welcome lights – number plate lighting
• not active
• turn on softly
• turn on hard
Number plate lights are turned on with welcome lights. (codable in REM)
**********************
Please see ...
http://support.mycarly.com/knowledge-base/code-bmw-what-is-possible/?utm_source=home&utm_medium=direct&utm_campaign=home
for latest information
**********************
0 件のコメント:
コメントを投稿